What Vibrating Screen Is Good For Sand Washing
Product classification: large screen machine series
TDYS series large round vibrating screen is mainly composed of screen box, screen mesh, vibrator and damping spring. The vibrator is installed on the side plate of the screen box and is driven by the motor through the coupling to rotate, generating centrifugal inertial force to force the screen box to vibrate.
Equipment advantages:
1. Powerful
Combining the characteristics and advantages of sand washing machine and fine sand recovery machine, it has the functions of water sand washing and fine sand dehydration and recovery, which is cleaner than the materials in the cleaning process of traditional sand washing machine.
2. High cleaning rate, green and environmental protection
The utility model has the advantages of high working efficiency, low energy consumption, energy conservation and environmental protection.
3. Simple structure and easy operation
The all-in-one machine has reasonable structure design, small floor area, simple installation, and the overall operating system process is more portable. One person can complete the operation every day, and the investment management cost is low.
4. Durable and long service life
With high-quality slurry pump, the blades are not easy to wear and more durable. Compared with the general slurry pump, the overall service life can be extended by 2-3 times, and the maintenance cost is low.
Product introduction
TDYS series large round vibrating screen is mainly composed of screen box, screen mesh, vibrator and damping spring. The vibrator is installed on the side plate of the screen box and is driven by the motor through the coupling to rotate, generating centrifugal inertial force to force the screen box to vibrate. The screen mesh of this series of vibrating screen is the main vulnerable part. According to the material variety and user requirements, high manganese steel textile screen mesh, perforated screen plate and rubber screen plate can be used. There are two kinds of screen plates: single-layer and double-layer. All kinds of screen plates can meet the requirements of high screening efficiency, long service life and no blocking. This series of shale shakers are seat mounted, and the screen surface inclination can be adjusted by changing the position and height of the spring support. The motor is installed on the left side of the screen frame and can also be installed on the right side of the screen frame. If there is no special requirement, the manufacturer shall install and supply the motor on the right side of the material movement direction.
Product classification: large screen machine series
TDYS series large round vibrating screen is mainly composed of screen box, screen mesh, vibrator and damping spring. The vibrator is installed on the side plate of the screen box and is driven by the motor through the coupling to rotate, generating centrifugal inertial force to force the screen box to vibrate.
Product introduction
TDYS series large round vibrating screen is mainly composed of screen box, screen mesh, vibrator and damping spring. The vibrator is installed on the side plate of the screen box and is driven by the motor through the coupling to rotate, generating centrifugal inertial force to force the screen box to vibrate. The screen mesh of this series of vibrating screen is the main vulnerable part. According to the material variety and user requirements, high manganese steel textile screen mesh, perforated screen plate and rubber screen plate can be used. There are two kinds of screen plates: single-layer and double-layer. All kinds of screen plates can meet the requirements of high screening efficiency, long service life and no blocking. This series of shale shakers are seat mounted, and the screen surface inclination can be adjusted by changing the position and height of the spring support. The motor is installed on the left side of the screen frame and can also be installed on the right side of the screen frame. If there is no special requirement, the manufacturer shall install and supply the motor on the right side of the material movement direction.
Main purpose
TDYS series large round vibrating screen is a product developed by our company according to the user's needs and the absorption technology. The moving track of the screen box of this series of round vibrating screen is round, which is suitable for screening coal, limestone, crushed stone, gravel, metal or non-metallic ore and other materials.
Installation and commissioning
1. During installation, steel plates shall be embedded according to the requirements of the equipment drawings. The upper plane of the embedded steel plates shall be on the same horizontal plane. The embedded steel plates and anchor bolts required for installation shall be prepared by the installation department. The supporting spring of each screen machine shall be selected before installation to ensure that the height and stiffness of each spring are basically the same.
2. After leaving the factory, if the installation lasts for more than 6 months, the bearing in the vibrator must be removed and cleaned before installation, and new grease (No. 2 lithium base grease) must be injected. After reinstallation of this series of shale shaker, the eccentric shaft shall be rotated by hand without excessive resistance or jamming, or the causes shall be found out and adjusted in time.
3. After all components are installed and checked as qualified, the test run can be carried out. Before the test run, the bolts at all places shall be checked in detail to see whether they are fastened and whether there are obstacles around the screen machine that hinder the vibration of the screen frame.
4. Test run for 4-6 hours, and observe the operation of the screen machine. In case of abnormal sound or vibration loss, stop the machine in time to check the cause and eliminate the fault. During test run, the following items shall be checked: (1) The temperature of vibrator bearing shall not exceed 75 ºC for high temperature and 45 ºC for temperature rise. (2) The fastening of fastening bolts at all places shall be tightened timely and timely in case of looseness.
5. After the test run is qualified, it can be put into production. Within the first two weeks after the screen machine is put into production, the fastening bolts shall be retightened once a week and then once a month.
Technical Parameter
About Transportation
After you place the order and pay the deposit, we will start to arrange the production and contact the ocean freight transportation agency to reserve the position. Two days before the end of production, you need to complete the final payment. Then, we inform the ocean cargo transportation agent company that it is ready to come to the factory to pull the goods to the port. On the day of delivery, we will send the customer the factory video and pictures, and mark the corresponding English name of each product and product parts with a marker to prevent the customer from not knowing what each part is after receiving the goods. At the same time, we will put the English version of the product instructions in the cargo box. We generally select freight forwarders with preferential prices for customers to deliver goods for you. The shipping method can be FOB or CIF. You can also choose EXW, and then contact the goods agent company yourself.
FAQ
1. Who are we?
Our headquarters is located in Henan, China, and our factory was established in 2002. At present, there are more than 100 workers, technical engineers, foreign trade sales personnel, and administrative personnel. The factory covers an area of more than 2000 square kilometers and is mainly engaged in vibrating screening and conveying and feeding equipment.
2. How do we guarantee the quality?
Always provide pre-production samples before mass production; Always carry out a final inspection before shipment.
3. What can you buy from us?
You can purchase a vibrating screen, roller screens, rotary screens, vacuum conveyors, mixer, and customized vibrating machinery and conveying equipment in our factory.
4. What are our strengths?
As one of the old enterprises in the screening industry, Tianfeng has provided a large number of screening equipment and systems at home and abroad. Mass production, rapid delivery, stable quality, affordable price, and excellent after-sales service have become the symbols of Tianfeng.
5. What services can we provide?
Accepted delivery conditions: FOB, CFR, CIF, EXW, CIP, FCA, CPT, DDP, express;
Accepted payment currency: USD, EUR, RMB;
Type of payment accepted: telegraphic transfer, letter of credit, express remittance, credit card, PayPal, Western Union remittance, cash, custody;
Oral: English, Chinese, French.
6. What information do we need to help you choose a perfect machine?
-Name and characteristics of raw materials.
-Purpose of use: remove impurities, filter, and grade.
-Processing capacity: kg/h, L/h.
-Raw material size: (mesh or mm).
-How many floors do you need?
-Voltage, frequency, phase (single-phase or three-phase) Note: You'd better send us the relevant pictures or materials you want to filter, which can ensure that we recommend the appropriate machine for you.
Equipment advantages:
){kind=link}