Linear vibrating screen industrial electric vibrating screen machine for separating plastic, stainless steel, small vibrating screen machine for grain sorting
In the process of using the vibrating screen, the motor burn is a more common problem, what are the reasons that can lead to the occurrence of such failures?
First, loose bolts cause motor burn. Loose bolts are one of the main reasons for motor burnout. The vibration force generated by the vibration motor at work will impact the anchor bolt two thousand times per minute. Moreover, the motor itself also takes part in vibration, most of which make the anchor bolt very easy to loosen. If one of the bolts is loose, it will cause the other bolts to loosen, which will cause breakage, thus burning the motor.
Method:
1, ensure the good contact of the motor floor in the floor area, so that several anchor bolts are evenly stressed;
2, often reinforce the anchor bolts;
3. Increase the anti-loose picking device. On material selection, the manager uses a vibration motor with shell and seat. Such a motor is processed in one time, so it can ensure the level. Shell seat allogeneic motor is processed and then assembled, so it is not easy to ensure the level, so that the force of the anchor bolt is not easy to be uniform, easy to cause the loosening and fracture of the anchor bolt.
Two, improper installation caused by motor burn; The upper and lower ends of the vibration motor are equipped with eccentric block, vertical or inclined installation requires the bearing axial bearing eccentric block gravity, if there is no plane bearing on the facade of the vibration motor will have an adverse effect on the bearing and shorten its service life.
Method:
1, choose vertical vibration motor (i.e. add plane bearing inside)
2, try to avoid vertical or inclined installation.
3. Improper adjustment of eccentric block causes motor burn; When adjusting the eccentric block, we must pay attention to its symmetry, that is to say, the eccentric block at both ends should correspond in pairs, if the wrong direction of the eccentric block at both ends is reversed, so that the vibration motor produces a space distortion, so that it works in an abnormal state, it will cause the motor to burn. Therefore, the center of gravity connection line of the eccentric block at both ends of the motor should be parallel to the rotating shaft, and can not be in a state.
Four, the protective cover seal is not strict, resulting in motor burn; Vibration motor mostly works in a large dust environment, in this case, if the protective cover seal is not strong enough, it is easy to enter the dust, causing the friction operation of the eccentric block, and then burn the motor. Therefore, we must strengthen the sealing of the protective cover and clean the dust inside the protective cover regularly
Applicable industries
It is divided into dry powder granular type and liquid type.
Chemical sieve: special sieve for resin, pigment, medicine, medicine, cosmetics, fire suppressant, plastic, rubber and other ceramics and refractory materials.
Special screens for ceramic refractory materials: abrasives, abrasives, glass, alumina, ceramic slurry, clay slurry, refractories, quartz sand, titanium powder, powder, etc.
Food specific screen: sugar, monosodium glutamate, salt, fruit juice, starch, milk powder, grain, soybean milk, egg powder, various protein powder, etc.
Metallurgical special screen: ore, titanium oxide, zinc oxide, casting sand, metallurgical powder superhard alloy, electromagnetic materials, aluminum powder, various metal particles, etc.
Others: carbon black, carbon, cosolvent, activated carbon, wood powder pearl, etc.
Liquid special screen: paint, paint, and viscous liquid.
Technical parameters of linear vibrating screen
Guidance on use and maintenance of linear vibrating screen
1. The machine shall be equipped with electrical protection device.
2. At the initial operation stage of the machine, the anchor bolts shall be checked at least once a day to prevent looseness.
3. When the motor rotation direction does not meet the requirements, adjust the power supply phase sequence.
4. The motor shall be well lubricated, and lithium base grease (ZL-3) shall be added once every two weeks of operation. When refueling, an appropriate amount of lithium base grease shall be added through the oil cup. When sealed bearings are used, the motor is not equipped with oil cups.
5. After the machine has been running for 1500 hours, check the bearing and replace it immediately in case of serious damage.
6. When the machine is used again after being stopped for a long time, the insulation resistance should be measured, which should be greater than 0.5 megohm for 500 volt megger measurement.
Daily maintenance of linear vibrating screen
1. Before starting:
(1) Check whether the coarse mesh and fine mesh are damaged;
(2) Check whether the transportation support is removed.
2. At startup:
(1) Pay attention to whether there is abnormal noise;
(2) Whether the current is stable;
(3) Whether the vibration is abnormal.
3. After use: clean up after each use.
Regular maintenance of linear vibrating screen
Regularly check the coarse screen, fine screen and spring for fatigue and damage, and check whether all parts of the machine body are damaged due to vibration. The parts that need to be lubricated must be lubricated.
About Transportation
After you place the order and pay the deposit, we will start to arrange the production and contact the ocean freight transportation agency to reserve the position. Two days before the end of production, you need to complete the final payment. Then, we inform the ocean cargo transportation agent company that it is ready to come to the factory to pull the goods to the port. On the day of delivery, we will send the customer the factory video and pictures, and mark the corresponding English name of each product and product parts with a marker to prevent the customer from not knowing what each part is after receiving the goods. At the same time, we will put the English version of the product instructions in the cargo box. We generally select freight forwarders with preferential prices for customers to deliver goods for you. The shipping method can be FOB or CIF. You can also choose EXW, and then contact the goods agent company yourself.
FAQ
1. Who are we?
Our headquarters is located in Henan, China, and our factory was established in 2002. At present, there are more than 100 workers, technical engineers, foreign trade sales personnel, and administrative personnel. The factory covers an area of more than 2000 square kilometers and is mainly engaged in vibrating screening and conveying and feeding equipment.
2. How do we guarantee the quality?
Always provide pre-production samples before mass production; Always carry out a final inspection before shipment.
3. What can you buy from us?
You can purchase a vibrating screen, roller screens, rotary screens, vacuum conveyors, mixer, and customized vibrating machinery and conveying equipment in our factory.
4. What are our strengths?
As one of the old enterprises in the screening industry, Tianfeng has provided a large number of screening equipment and systems at home and abroad. Mass production, rapid delivery, stable quality, affordable price, and excellent after-sales service have become the symbols of Tianfeng.
5. What services can we provide?
Accepted delivery conditions: FOB, CFR, CIF, EXW, CIP, FCA, CPT, DDP, express;
Accepted payment currency: USD, EUR, RMB;
Type of payment accepted: telegraphic transfer, letter of credit, express remittance, credit card, PayPal, Western Union remittance, cash, custody;
Oral: English, Chinese, French.
6. What information do we need to help you choose a perfect machine?
-Name and characteristics of raw materials.
-Purpose of use: remove impurities, filter, and grade.
-Processing capacity: kg/h, L/h.
-Raw material size: (mesh or mm).
-How many floors do you need?
-Voltage, frequency, phase (single-phase or three-phase) Note: You'd better send us the relevant pictures or materials you want to filter, which can ensure that we recommend the appropriate machine for you.
){kind=link}